Syntech StopAQ zoom
Syntech StopAQ image 1
Syntech StopAQ image 2
Syntech StopAQ image 3

Syntech StopAQ

Plastic sealing paste for waterproofing tubes with passing cables

Mono-component Sealant compound, permanently plastic, slightly warm (+10% in volume in contact with water), for waterproofing underground holes, through which one or many wires and/or technical pipes pass, in masonry structures. It is extruded around the cables passing using specific dosing gun for 600 ml bags, and then covered with thixotropic mortar Repar Tix G2.
Components
Single-component
Appearance
Paste
Customs code
3214 9000

Request product info

    By submitting I agree to the privacy notice

    Lines of belonging
    Linea prodotto Aqua
    Linea prodotto Building
    Linea prodotto Infratech
    Thematic site
    ProSeal
    Features and benefits
    Where it is used
    How to use
    Technical data
    Additional content
    Warnings and precautions
    Media
    Related products

    Syntech StopAQ

    - It does not harden over time, while maintaining its original plasticity.
    - It is a non-toxic material.
    - It is easy to apply, it adheres both to dry and wet surfaces. Usable even in the presence of slight water seepage.
    - It expands slightly in contact with water (+10% ), thereby sealing any losses that may arise due to subsidence or vibration.

    Fields of application
    Waterproof sealing for drilled holes in walls of concrete, bricks, tufa, etc., which are crossed by passing electrical cables and/or technical tubes in general (gas, plumbing, etc.).
    Allowed supports
    Concrete
    Prefabricated concrete
    Bricks
    Tuff
    Mixed walls (bricks and stones)
    Stone walls
    Rock walls
    Preparation of supports
    Dust, soil, sand, loose parts, rust, and layers of paint of the pipes and old deteriorated sealant material must be removed with pressurised water or brushing, before applying the compound. The inner surface of the tube/hole containing the passing cables should be damp or wet.
    Mode of use
    To limit the thickness of Syntech StopAQ, it is recommended to insert a barrier of polyethylene foam kerbs with an appropriate diameter (Filtene Fondogiunto).

    Syntech StopAQ will be extruded into the hole to be sealed, taking care that the paste encompasses all the passing cables. Compact, with the help of a wooden handle or the like, the paste just extruded against the polyethylene "barrier" previously positioned to seal all the gaps. The depth of clogging made with Syntech StopAQ must be at least 8-10 cm.

    Smooth the outer surface of Syntech StopAQ, with special spatula or gloved hand, compacting it well. Finally, close the "mouth" outside of the tube/hole with Repar Tix G2, minimum 2 cm thick, smoothing around the cables with a spatula.

    Application methods
    Apply by hand
    Dispensing gun
    Spatula
    Tool cleaning
    Water
    Key features
    Density
    Density: 1.20 kg/dm³
    Hydroexpansive product
    Hydroexpansive product: +10 %
    Min. recommended thickness
    Min. recommended thickness: 8 cm
    Nonflammable
    Nonflammable
    Pot-life
    Pot-life: 90 min
    Shelf-life
    Shelf-life: 24 months
    Temperature of use
    Temperature of use: 0 / +50 °C
    Use wearing protective gloves
    Use wearing protective gloves
    Technical specifications

    Auto-ignition temperature

    >200 °C

    Flash-point

    >190 °C

    Resistance to water pressure

    1 bar
    Consumption
    Approximately 1.7 cartridges of Syntech StopAQ for each cubic decimetre of volume to be filled.
    Available colors
    Green
    Packaging and dimensions
    Cartridge 533 cc
    Storage and conservation
    Store the product in its original packing, in a fresh and dry environment, avoiding frost and direct sunlight.
    Additional content

    Photo Sequence

     

    Warnings
    In situations of low temperature (usually in winter) the cartridges of Syntech StopAQ must be heated in water to +35°C, for about a quarter of an hour, before being used ("bain marie" heating).
    For applications in steel pipes, provide a suitable layer of Syntech RGS epoxy primer on the surfaces that will be filled with Repar Tix G2.The general information, along with any instructions and recommendations for use of this product, including in this data sheet and eventually provided verbally or in writing, correspond to the present state of our scientific and practical knowledge.
    Any technical and performance data reported is the result of laboratory tests conducted in a controlled environment and thus may be subject to modification in relation to the actual conditions of implementation.

    Azichem Srl does not assume any liability arising from inadequate characteristics related to improper use of the product or connected to defects arising from factors or elements unrelated to the quality of the product, including improper storage.
    Those wishing to utilise the product are required to determine prior to use whether or not the same is suitable for the intended use, assuming all consequent responsibility.

    The technical and characteristic details contained in this data sheet shall be updated periodically. For consultation in real time, please visit the website: www.azichem.com. The date of revision is indicated in the space to the side. The current edition cancels out and replaces any previous version.

    Please note that the user is required to read the latest Safety Data Sheet for this product, containing chemical-physical and toxicological data, risk phrases and other information regarding the safe transport, use and disposal of the product and its packaging. For consultation, please visit: www.azichem.com.
    It is forbidden to dispose of the product and/or packaging in the environment.
    Photo gallery
    Video
    Technical Documentation
    Key features

    Richiedi info sul prodotto

      By submitting I agree to the privacy notice

      Copyright © 2024 All Rights Reserved
      Powered by Webplease
      magnifiercross