Explore products

Integrated solutions

Guide to selection

Themed sites

SYNTECH POLIUREA PRIMER – EPOXY
Two-component epoxy primer for cementitious surfaces, marble and wood
SYNTECH POLIUREA PRIMER – EPOXY
Two-component epoxy primer for cementitious surfaces, marble and wood
SYNTECH POLIUREA PRIMER – EPOXY
Two-component epoxy primer for cementitious surfaces, marble and wood

SYNTECH POLIUREA PRIMER – EPOXY

Two-component epoxy primer for cementitious surfaces, marble and wood

Code: SYN.0309

Components: 2

Appearance: Liquid + Thick liquid

SYNTECH POLIUREA PRIMER - EPOXY is a two-component primer based on modified epoxy resins and special hardeners, solvent-free. Specially formulated to provide the right compromise between impregnation and wettability of the support to which, once applied, it forms a well-bonded layer.

Customs Code

3907 3000

Linee di appartenenza

General characteristics

Density: 1.3 - 1.5 (A+B) g/cm³

Dosage: 350-700 g/m²

Use wearing protective gloves

Shelf-life: 6 months

Use wearing protective glasses

Solvent-free

Technical specifications

Gel time

100 - 200 min

Complete hardening

7 day

Longitudinal elongation at break

4 %

Hard to touch

>4 h

Concrete adhesion (cutting test)

>1.5 MPa

Viscosity

150 - 400 (A) / 2000 - 4000 (B) mPas

Available colours

- Milky white

Packaging and dimensions

- Can 20 kg [A]

- Canister 4 kg [B]

- Kit: 1 Can 20 kg [A] + 1 Canister 4 kg [B]

Consumption

From 350 to 700 g for each square metre, based on the intervention carried out on the support (bush-hammering, shot peening, etc.), the porosity of the support itself and the incorporation or not of quartz sand in the particle size and quantity proportionate to the intervention to be implemented.

Use fields

Adhesion promoter for epoxy, polyurethane and polureic coatings, adhesion promoter for porous and deteriorated substrates, consolidating agent for cement and concrete.

Preparation of supports

The support on which the polyurea or resinous system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" SYNTECH PAVIDAMP. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion.

Use method

Carefully mix component A to allow the correct homogenization of the fillers present; then combine it with component B in a suitable and large container. Then mix the compound with a mechanical stirrer at low speed until a homogeneous mixture is obtained.
When the support is ready, apply SYNTECH POLIUREA PRIMER - EPOXY using rollers, brushes or spatulas trying to obtain a dry film.

Application methods

- Brush

- Paint roller

- Spatula

Tool cleaning

- Thinner for resins

Permitted supports

- Cement-based or lime-based mortars

- Concrete

- Drywall

- Fiber-cement

- Floor screed

- Plasters

- Porphyry and natural stones

- Prefabricated concrete

- Rock walls

- Stone walls

- Tiles

- Tuff

- Wood

Warnings, precautions and Ecology

Avoid contact with skin and mucous membranes. Use appropriate protection, in particular, a mask and gloves. Do not inhale the product, and if possible, ventilate the work areas.