SYNTECH PAVISHEER

Epoxy treatment for transparent coatings

Code: SYN.0106

Components: 2

Appearance: Liquid

Two-component transparent epoxy system, based on epoxy resins in aqueous dispersion, free from solvents, characterised by a high content of solids that provides, after application and curing, a coating with good mechanical resistance and chemical, especially related to contact with oils and solvents.

Linee di appartenenza

Certification obtained and Standards

Products and systems for the protection and repair of concrete structures - Surface protection systems for concrete

EN 1504-2

Products and systems for the protection and repair of concrete structures - Surface protection systems for concrete

General characteristics

density

Density: 1.09 kg/l

mixing-ratio

Mixing ratio: 1:1 _

nonflammable

Nonflammable

pot-life

Pot-life: 80 -120 min

shelf-life

Shelf-life: 12 months

solvent-free

Solvent-free

temperature-of-use

Temperature of use: +5 / +35 °C

to-be-applied-in-two-coats

To be applied in two coats

use-wearing-protective-gloves

Use wearing protective gloves

Technical specifications

Capillary absorption

0.02

Complete hardening

7 day

Hard to touch

0.5 h

Viscosity

Comp A 14700 / Comp B 20500 mPa

Walkability

24 h

Available colours

- Transparent

Packaging and dimensions

- Can 10 kg [B]

- Can 10 kg [A]

- Can 5 kg [A]

- Can 5 kg [B]

- Canister 1 kg [A]

- Canister 1 kg [B]

- Kit: 1 Canister 1 kg [A] + 1 Canister 1 kg [B]

- Kit: 1 Can 5 kg [A] + 1 Can 5 kg [B]

- Kit: 1 Can 10 kg [A] + 1 Can 10 kg [B]

Consumption

From 0.10 to 0.15 kg of SYNTYECH PAVISHEER for each square metre of surface to be covered.

Use fields

Transparent finish of interior floor coverings, mechanical-resistant impregnations, anti-dust and anti-oil for concrete surfaces.

Preparation of supports

The media should have adequate mechanical resistance. The concrete surfaces should be cured, dry, planar and absorbent, free from oils, detergents, powders and soiling. The most appropriate type of mechanical preparation should also be determined (degreasing or shot peening).

Conveniently absorbent surfaces may be dealt with directly after a proper cleaning. For tiled surfaces and for pre-existing coverings in resin, a degreasing or shot peening treatment is required until complete opacification and complete elimination of dust.

Use method

Mix components A and B each in their own container before mixing. Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Pour component B into a suitable container and add component A. Mix everything for a few minutes using a mechanical stirrer with variable speed until a homogeneous and uniform color mixture is obtained. Leave to rest for a few minutes and mix again. Dilute the final product only with water in the SYNTECH PAVISHEER: water ratio of 1: 3 for the first coat and 1: 2 for the second. Gradually add the dilution water, continuing to mix for a few minutes. The dilution ratio can vary according to the porosity of the support; if necessary on closed surfaces it is also possible to dilute the second coat respecting the dilution ratio 1: 3. The SYNTECH PAVISHEER emulsion has a stability of about 2 hours at 20 ° C; within this period the product must be used. SYNTECH PAVISHEER is applied with a short-haired roller or spray, covering the entire surface evenly. We recommend application at temperatures not lower than 5 ° C.

Application methods

- Brush

- Paint roller

Tool cleaning

- Water

Permitted supports

- Concrete

- Prefabricated concrete

- Tiles

- Floor screed

- Rock walls

Contact us now

Vuoi saperne di più sui nostri prodotti?

Attention, correctly compile this field.
Attention, enter a valid email address.
Attention, correctly compile this field.

By submitting I accept the privacy policy

Attention, correctly compile this field.

Subscribe to the newsletter

Share

Products on display

  • Opus Dry
  • Sanageb
  • Floortech Prerit