SYNTECH PAVICROM

Coloured epoxy coating for concrete flooring

Code: SYN.0105

Components: 2

Appearance: Liquid

A 2-component coloured finish, with an epoxy resin base in aqueous dispersion. Ideal for the pigmented coating of industrial flooring and concrete products in general. Surfaces treated with SYNTECH PAVICROM are easy to clean and provide excellent resistance to mechanical wear, as well as having a high resistance to water, alkaline solutions, detergents and hydrocarbons (oils, diesel, petrol, etc.).

Linee di appartenenza

Certification obtained and Standards

Products and systems for the protection and repair of concrete structures - Surface protection systems for concrete

EN 1504-2

Products and systems for the protection and repair of concrete structures - Surface protection systems for concrete

General characteristics

density

Density: 1.15 kg/l

dosage

Dosage: 250 - 400 g/m²

mixing-ratio

Mixing ratio: 1:0.3 _

nonflammable

Nonflammable

pot-life

Pot-life: 30 - 60 min

shelf-life

Shelf-life: 12 months

solvent-free

Solvent-free

temperature-of-use

Temperature of use: +5 / +35 °C

to-be-applied-in-two-coats

To be applied in two coats

use-wearing-protective-glasses

Use wearing protective glasses

use-wearing-protective-gloves

Use wearing protective gloves

Technical specifications

Comp A 1.55 kg/l / Comp B 1.10 kg/l %

3 MPa

Capillary absorption

< 0.021

Complete hardening

10 day

Dry residue

100 %

Hard to touch

4 - 8 h

Permeability to CO2

2140 m

Permeability to water vapor

Classe II (12 m) _

Resistance to abrasion

< 150 mg

Time before second coat

6 - 24 h

Viscosity

Comp A: 11300 / Comp B: 8800 mPas

Available colours

- Flame red

- Agate grey

Packaging and dimensions

- Can 10 kg [A]

- Can 3 kg [B]

- Kit: 1 Can 10 kg [A] + 1 Can 3 kg [B]

- Can 5 kg [A]

- Can 1.5 kg [B]

- Kit: 1 Can 5 kg [A] + 1 Can 1.5 kg [B]

Consumption

In two coats, apply 0.25 to 0.40 kilograms of SYNTECH PAVICROM per square metre of surface to be covered.

Use fields

For protective and decorative painting of concrete floors, reviving the colour of old resin flooring, wall plinth enamelling, and so on. Perfect for mechanical workshops, manufacturing industries, warehouses and factories generally in which special and high chemical and mechanical resistance are required.

Preparation of supports

Thoroughly clean and degrease the surfaces, removing stains, paint residues and loose parts of any kind. Determine the most convenient type of mechanical preparation (sandblasting, hydrowashing, etc.). Surfaces are also to be free of patchiness and, where appropriate, levelled and smoothed with REPAR TIX BIC or REPAR SM BIC. Apply by roller, brush or spray with approximately 300 to 500 g/m2 of SYNTECH PRIMER EP to consolidate the surface and facilitate the adhesion of the subsequent coating. Apply SYNTECH PAVICROM upon complete drying of the primer and no later than 24 hours. In the event of the presence (even suspected) of moisture resulting from capillary rising phenomena from the substrate, it is recommended to first apply SYNTECH PAVIDAMP, the epoxy resin for “wet surfaces”.
Tiled floors or surfaces with pre-existing resin must be subjected to mechanical roughening performed by peening, milling, bushhammering, and so on, until the waterproof crust and opaque surfaces have been entirely eradicated. Remove the dust following the abrasion.

Use method

Mix component A and component B separately, directly in their packages, in advance. When applying, combine the two components into a single container and thoroughly mix for 2 minutes using appropriate equipment (trolling motor). To prevent any errors in the mixing ratio that would result in a lack of or incomplete hardening, do not extract partial quantities from the packaging. Next, pour component B into the container of component A.
SYNTECH PAVICROM is applied with a “short-pile” roller within 24 hours after applying the primer. Add the dilution water: the first coat diluted with water at a rate of 10 ÷ 20% depending on the porosity, cohesion of the support and the temperature; the second finish must be diluted by 6 ÷ 11%. After adding the dilution water, continue mixing for a few minute.
We recommend applying two overlapping coats of the product, at temperatures not lower than +5° C. The second coat must be applied within 24 hours. 3-5% by weight of quartz B0 or B1 (or hollow glass microspheres) can also be added to achieve a non-slip effect.

Application methods

- Brush

- Paint roller

Tool cleaning

- Water

Permitted supports

- Concrete

- Prefabricated concrete

- Tiles

- Floor screed

Contact us now

Want to know more about our products?

Attention, correctly compile this field.
Attention, enter a valid email address.
Attention, correctly compile this field.

By submitting I accept the privacy policy

Attention, correctly compile this field.

Subscribe to the newsletter

Share

Products on display

  • Sanawarme
  • Protech Balcony
  • Sanageb