Sanalit zoom
Sanalit image 1
Sanalit image 2
Sanalit image 3

Sanalit

Lime-based conglomerate for lightweight, insulating slabs and screeds

Fiber-reinforced premix, based on hydraulic lime, light aggregates with high communicating porosity and cork flours, for the realization, with the sole addition of water, of screeds and lightweight substrates, with high thermal and acoustic insulation, in green building interventions and in restoration of period and monumental buildings. Sanalit screeds, packaged according to the specifications shown in this technical data sheet, are classified C5-F1-A22 in accordance with European standard EN 13813.
Components
Single-component
Appearance
Powder
Customs code
3824 5090

Request product info

    By submitting I agree to the privacy notice

    Obtained Certifications and Regulations
    EN 13813
    Lines of belonging
    Linea prodotto Building
    Linea prodotto Floor
    Linea prodotto Sanageb
    Thematic site
    Sanageb
    Where it is used
    How to use
    Technical data
    Additional content
    Warnings and precautions
    Media
    Related products
    Fields of application
    For laying subbase screeds in high performance thermo-acoustic ecological buildings.
    Allowed supports
    Concrete
    Floor screed
    Preparation of supports
    Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface".
    Mode of use
    Pour about 2/3 of the mixing water into the mixer. Gradually add Sanalit and the water still needed, by mixing until a homogeneous lump-free mixture of the desired consistency is obtained. Support the product at the reference height and float until a smooth and planar surface is obtained, preparing the joints beforehand where necessary. The mixing water indicatively necessary is equal to 65-75% by weight (8.5 -9.5 litres per 13 kg bag).
    Application methods
    Finishing trowel
    Pump
    Spatula
    Straight edge
    Tool cleaning
    Water
    Key features
    Maximum diameter of aggregate
    Maximum diameter of aggregate: 2.5 mm
    Mix with water
    Mix with water: 25 - 35 %
    Pot-life
    Pot-life: 60 mm
    Shelf-life
    Shelf-life: 12 months
    Temperature of use
    Temperature of use: +6 / +30 °C
    Technical specifications

    Compressive strength after 7 days
    UNI EN 1015-11

    4.0 MPa

    Compressive strength after 28 days
    UNI EN 1015-11

    > 5.0 MPa

    Flexural strength after 7 days
    UNI EN 1015-11

    1.0 MPa

    Flexural strength after 28 days
    UNI EN 1015-11

    > 1.6 MPa

    pH

    12

    Bonding force
    UNI EN 1542

    0.5 N/mm²

    Breathability
    UNI EN 1015-19

    11 μ

    Reaction to fire

    A1

    Thermal conductivity
    UNI EN 1745 - EN 12664

    0.21 W/mK

    Density
    UNI EN 1015-6

    1150 kg/m³

    Capillary absorption
    UNI EN 1015-18

    0.50 kg•h^0.5/m²
    Consumption
    Approximately 6 kg/m² of Sanalit for every centimetre of thickness to be implemented (approximately 600 kg per cubic metre).
    Available colors
    Light gray
    Packaging and dimensions
    Bag 13 kg
    Pallet: 50 x (Bag 13 kg)
    Storage and conservation
    Store the product in its original packing, in a fresh and dry environment, avoiding frost and direct sunlight.
    Additional content

    Warnings
    It is always essential to carry out preliminary tests to check the appropriateness of the product, depending on specific requirements.

    Protect fresh surfaces from direct exposure to sunlight, from the rain and the wind, and cure the prolonged moist hardening.

    Please note that Sanalit is only intended as a subbase for subsequent cement or lime-based slabs. It should not be used as a top trampling layer.The general information, along with any instructions and recommendations for use of this product, including in this data sheet and eventually provided verbally or in writing, correspond to the present state of our scientific and practical knowledge.
    Any technical and performance data reported is the result of laboratory tests conducted in a controlled environment and thus may be subject to modification in relation to the actual conditions of implementation.

    Azichem Srl does not assume any liability arising from inadequate characteristics related to improper use of the product or connected to defects arising from factors or elements unrelated to the quality of the product, including improper storage.
    Those wishing to utilise the product are required to determine prior to use whether or not the same is suitable for the intended use, assuming all consequent responsibility.

    The technical and characteristic details contained in this data sheet shall be updated periodically. For consultation in real time, please visit the website: www.azichem.com. The date of revision is indicated in the space to the side. The current edition cancels out and replaces any previous version.

    Please note that the user is required to read the latest Safety Data Sheet for this product, containing chemical-physical and toxicological data, risk phrases and other information regarding the safe transport, use and disposal of the product and its packaging. For consultation, please visit: www.azichem.com.
    It is forbidden to dispose of the product and/or packaging in the environment.
    Photo gallery
    Technical Documentation

    Richiedi info sul prodotto

      By submitting I agree to the privacy notice

      Copyright © 2024 All Rights Reserved
      Powered by Webplease
      magnifiercross